How to turn off Raspberry Pi?

 To safely turn off a Raspberry Pi, do one of these:



From the terminal (recommended)

  • Shutdown now

sudo shutdown -h now

  • Power off immediately

sudo poweroff

  • Halt (stops CPU; usually also powers off)

sudo halt

With a desktop GUI

  • Click Menu (Raspberry icon) → Shutdown… → Shutdown

If it’s frozen

  • Try the “magic SysRq” safe reboot sequence (works only if enabled):

    1. Hold Alt + PrintScreen

    2. Slowly type: R E I S U B
      (reboots safely; for shutdown you’d usually still need power control afterward)

After shutdown

When the Pi finishes shutting down, the green ACT LED stops blinking.
Then you can remove power (unless you have a power management board that cuts power automatically).

评论

发表评论

此博客中的热门博文

Detailed Explanation of STM32 HAL Library Clock System

图片
  The   STM32 HAL (Hardware Abstraction Layer) Library   provides a structured way to configure and manage the   clock system   in STM32 microcontrollers . The clock system is crucial because it determines the speed at which the CPU, peripherals, and buses operate. This guide explains the   HAL clock initialization process, clock tree, and configuration methods . 1. STM32 Clock Tree Overview The STM32 clock system is highly flexible, allowing multiple clock sources and distribution paths. The main components are: A. Clock Sources Source Description Typical Use HSI  (High-Speed Internal) 8-16 MHz RC oscillator (low accuracy, no external component) Fallback clock, default at startup HSE  (High-Speed External) 4-48 MHz crystal/oscillator (high accuracy) Main system clock, PLL input LSI  (Low-Speed Internal) ~32 kHz RC oscillator (low power, low accuracy) RTC, watchdog timer LSE  (Low-Speed External) 32.768 kHz crystal (high accuracy) RTC, ...
阅读全文

How do you set up ADC (Analog-to-Digital Converter) in STM32?

图片
  Setting up the   ADC (Analog-to-Digital Converter)   in an STM32 microcontroller involves configuring the ADC peripheral to read analog signals from one or more input channels and convert them into digital values. STM32 microcontrollers have highly flexible ADC peripherals, and the setup process can vary slightly depending on the specific STM32 series (e.g., STM32F1 , STM32F4 , STM32H7 ). Below is a general guide to setting up the ADC in STM32 using   STM32CubeMX   and   HAL (Hardware Abstraction Layer)   libraries. 1.  Hardware Setup Connect the analog signal source (e.g., a sensor or potentiometer) to the ADC input pin on the STM32. Ensure the analog signal voltage is within the ADC's input range (typically 0V to 3.3V for most STM32 devices). 2.  Software Setup Using STM32CubeMX STM32CubeMX is a graphical tool provided by STMicroelectronics to configure STM32 peripherals and generate initialization code. Steps: Open STM32CubeMX: Create...
阅读全文

How To Connect Stm32 To PC?

图片
Connecting an STM32 microcontroller to a PC typically involves using a communication interface such as USB , UART (serial) , SPI , or I2C . The most common and straightforward method is through USB or UART . Below, I’ll explain how to connect your STM32 to a PC using these methods. Method 1: Using USB (Direct Connection via Virtual COM Port) Many STM32 boards, such as the STM32 Nucleo or STM32 Discovery series, have a built-in USB-to-serial interface, which allows you to communicate with your PC via a virtual COM port . Steps for Connecting via USB: Use a USB Cable : If your STM32 board has a built-in USB interface (e.g., STM32 Nucleo boards ), simply use a micro-USB or USB-C cable to connect the board to your PC. Install Drivers (if required) : Some STM32 boards (e.g., those with ST-Link or USB to UART interfaces) might require drivers to be installed on your PC. Visit the STMicroelectronics website and download the appropriate ST-Link drivers or Virtual COM Port (VCP) dri...
阅读全文