博文

目前显示的是标签为“Arduino”的博文

How to program an Arduino?

图片
 To program an Arduino , you basically: install the IDE → connect the board → pick the right board/port → write (or open) a sketch → upload → verify it runs . 1) Install the Arduino IDE Download Arduino IDE 2.x from Arduino’s official site (or use Arduino Web Editor). 2) Connect your Arduino Plug the Arduino into your PC with a USB cable. If it’s a clone board (especially with CH340 / CP2102 ), you may need a USB-serial driver. 3) Select board + port in the IDE In Arduino IDE: Tools → Board : choose your model (e.g., Arduino Uno , Nano , Mega 2560 ). Tools → Port : select the COM port (Windows) or /dev/tty... (Mac/Linux). 4) Write your first program (Blink) Open: File → Examples → 01.Basics → Blink Or paste this: // Blink LED on pin 13 (most boards have a built-in LED on 13) void setup () { pinMode (LED_BUILTIN, OUTPUT); } void loop () { digitalWrite (LED_BUILTIN, HIGH); delay ( 500 ); digitalWrite (LED_BUILTIN, LOW); delay ( 500 ...

How to load program in Arduino?

图片
 To “load a program” onto an Arduino , you’re basically compiling your sketch and uploading it to the board over USB (or via an external programmer). Here are the common ways. Method 1: Arduino IDE (most common) Install Arduino IDE (Arduino IDE 2.x). Connect the board to your PC with USB. In IDE: Tools → Board → pick your Arduino model (Uno/Nano/Mega, etc.). Tools → Port → select the COM/USB port that appears. Open an example: File → Examples → 01.Basics → Blink Click Verify (✓) to compile. Click Upload (→) to load it onto the Arduino. The board will reset and run the program automatically. Quick check: The “L” LED should blink after uploading Blink. Method 2: Upload using a USB-to-Serial adapter (for some boards) Used when: Your board doesn’t have USB built-in, or You’re programming a bare ATmega328P + bootloader setup. Typical wiring (adapter → Arduino/ATmega): TX → RX RX → TX GND → GND 5V → 5V (only if the adapter pr...

How to find model of microcontroller for Arduino IDE?

图片
 In Arduino -land, the “ microcontroller model” is usually determined by which Board (and sometimes Processor) you select in the IDE. If you don’t know what chip is on the board, there are a few reliable ways to find it. 1) The fastest: check Tools → Board (and Tools → Processor ) Connect the board. In Arduino IDE: Tools → Board : pick (or confirm) the board family (Uno, Nano, Mega, ESP32 Dev Module, Pico, etc.) Tools → Processor (only appears for some AVR boards like Nano/Pro Mini): this often directly shows the MCU choice, e.g. ATmega328P vs ATmega168 . If you see a “Processor” submenu, that’s basically your answer. 2) Arduino IDE 2.x: Tools → Get Board Info With the board plugged in and the correct Tools → Port selected: Tools → Get Board Info shows things like board name , VID/PID , and sometimes the identified board profile. This won’t always print the exact MCU model, but it helps you confirm the board family so you can map it to the MCU. 3...

How to collect Arduino serial print data?

图片
 Here are the most practical ways to collect (log) Arduino Serial.print() data —from quick manual capture to fully automated logging. 1) Arduino IDE Serial Monitor (quick + manual) Open Tools → Serial Monitor Select the correct baud rate You can copy/paste the text out. IDE 2.x also has a Serial Plotter (good for quick graphs, not great for saving clean logs). Best for: quick debugging. 2) Use a terminal program and log to a file (easy + reliable) Windows PuTTY Find the COM port (Device Manager) In PuTTY: Connection type = Serial , set COMx and baud Enable logging: Session → Logging → “All session output” → choose a log file Open the session → your serial data is saved. Tera Term File → Log… to save the session output. macOS / Linux Use screen to view, and tee to save: # replace /dev/ttyACM0 or /dev/ttyUSB0 with your device, and 115200 with your baud screen /dev/ttyACM0 115200 For logging, screen alone isn’t great; better use pyse...

What does analogWrite() do in Arduino?

图片
  analogWrite() makes an Arduino pin output a PWM (pulse-width modulated) signal that behaves like an “analog” level to things like LEDs and DC motors. What it actually does Outputs a square wave that switches HIGH/LOW quickly. You set a value (usually 0–255 ) that controls the duty cycle (how long it stays HIGH each cycle). analogWrite(pin, 0) → always OFF (0% duty) analogWrite(pin, 255) → always ON (100% duty) analogWrite(pin, 128) → ~50% duty What it’s used for LED dimming (brightness follows duty cycle) Motor speed control (with a driver/ MOSFET ) Generating a basic PWM control signal (e.g., for some devices) Important notes It only works on PWM-capable pins (marked with ~ on many boards). It does not output a true analog voltage by itself. If you want a real DC voltage, you need: a low-pass RC filter , or a DAC pin (some boards like Due/Zero have DAC ), or an external DAC. PWM frequency depends on the board ...

How to use LCD on Arduino?

图片
 You use an LCD on Arduino by doing two things : Wire it correctly Use the LiquidCrystal (or I2C) library in your sketch I’ll show you both the classic 16×2 LCD with parallel pins and the I2C backpack version. 1. The LCD we’re talking about Most tutorials (and this answer) assume a 16×2 character LCD that’s “HD44780-compatible”, like this: 16 characters × 2 lines Pins: VSS, VDD, VO, RS, RW, E, D0–D7, A, K If yours has only 4 pins (GND, VCC, SDA, SCL) → that’s an I2C backpack version. I’ll cover that in section 4. 2. Wiring a 16×2 LCD directly to Arduino (4-bit mode) We’ll use 4 data lines (D4–D7) to save pins. Parts: Arduino Uno (any board is fine) 16×2 LCD 10 kΩ potentiometer (for contrast) Some jumper wires Optional: 220 Ω resistor for LCD backlight Typical wiring table (4-bit mode) Assume these connections: LCD Pin Name Connect To 1 VSS GND 2 VDD +5V 3 VO Middle pin of 10k pot (contrast) Pot side 1 → GND, side 2 → +5V 4 RS A...

How to program an Arduino?

图片
  You “program” an Arduino by writing a sketch (a C/C++ program), compiling it, and uploading it to the board over USB. Let’s walk it from zero to blinking LED. 1. What you need An Arduino board (Uno, Nano, Mega, etc.) USB cable that matches your board (Uno: USB-B, newer: USB-C/micro-USB) A computer (Windows / macOS / Linux) Arduino IDE installed If you don’t have the IDE yet, download it from the official Arduino site (Arduino IDE 2.x). Install it like any normal app. 2. Connect the Arduino Plug the USB cable into the Arduino and your computer. The power LED on the Arduino should turn on. Windows may install a driver automatically; on macOS and Linux it usually just works. 3. Open the Arduino IDE and select your board Start Arduino IDE . Go to Tools → Board and choose your board, for example: Arduino Uno Arduino Nano Arduino Mega or Mega 2560 , etc. Go to Tools → Port and pick the port that shows something like: COM3 (...

How to do wiring for shield board for Arduino Nano in KiCad?

图片
Think of an Arduino Nano shield PCB in KiCad as: A board with two rows of female headers that match the Nano’s pins, plus whatever parts you want to connect to those pins. “Wiring” is really just connecting Nano pins (on the schematic) to your parts , then routing those nets on the PCB. I’ll walk you through it step-by-step. 1. Decide what the shield should do Before KiCad: Which Nano pins do you need? (D2–D13, A0–A7, 5V, 3V3, GND, VIN…) What will you connect? e.g. joystick module: X→A0, Y→A1, SW→D2 LEDs on D3/D5 I2C connector on A4/A5, etc. Write this mapping down; you’ll literally implement that in the schematic. 2. In the schematic: use Nano symbol as the “connector” Assuming you already have an Arduino Nano symbol (from previous step / library): Create a new KiCad project for the shield. Open Schematic Editor . Place the Arduino Nano symbol This symbol represents the female headers where the Nano will plug in. Its pins D0, D1, 5V, GND… are yo...

Does all microcontroller code run in loop?

图片
Short answer: almost all applications on microcontrollers are designed to run “forever”, usually inside some kind of loop – but not every single line of code is literally inside a while(1) loop. Let’s unpack that a bit. 1. Why “infinite loop” is so common Microcontrollers usually: Power up Run some startup code (set up stack, clocks, memory) Call your main() Then are expected to run as long as the device has power Unlike a PC program, there’s no operating system saying “OK, you’re done now, exit”. So firmware is typically structured as: int main ( void ) { setup_peripherals(); init_stuff(); while ( 1 ) { // “superloop” read_inputs(); update_state(); control_outputs(); } } This is why you see so many: while(1) in bare-metal C for(;;) in some code loop() function in Arduino (which the core actually calls in a loop internally) So: the top-level logic is usually in a forever loop . 2. But not everything ...